Kaplun P.V., Gonchar V.A. Complex criterion of assessment of contact experience of structural elements with nitrogen coatings at termination.

  • П.В. Каплун
  • В.А. Гончар

Abstract

The complex coefficient of estimation of quality of composition is offered it is "nitrided coverage-basis" taking into account the thickness of coverage, hardness of surface and basis,gradient of hardness of coverage and maximal remaining tensions in coverage on the criterion of her maximal pin endurance at the friction of woobling. Key words: coverage, coefficient, basis, quality, gradient.

References

1. Kaplun V.G. Ionnoe azotirovanie v bezvodorodnyh sredah / V.G. Kaplun P.V. Kaplun // Hmel'nic'kij – HNU.– 2015.–344s.
2. Trubin G.K. Kontaktnaja ustalost' materialov dlja zubchatih koles. M, Mashgiz, 1962, – 404s.
3. Zinchenko V.M. Inzhenerija poverhnosti zubchatih koles metodami himiko-termicheskoj obrabotki.—M.:Izd-vo MGTU im.N.Je.Baumana, 2001.-303s.
4. Tesker E.I. Kontaktnaja prochnost' cementovannyh i nitrocementovannyh zubchatih koles.//MiTOM.1988.№2.S.46—50.
5. Bakjengem E. Rukovodstvo po proektirovaniju zubchatih peredach, chasti 2 i 3. Mashgiz, 1948.
6. Moroz L.S. ,Shurakov S.S. Problema prochnosticementovannoj stali L. :Mintransmash, 1947, .228s.
7. Zalko A.I. Soprotilenie ustalosti vysokonagruzhennyh zubchatih koles iz razlichnyh stalej //Vestnik mashinostroenija. 1988. №8. S.57—59.
8. Saverin M.M. Kontaktnajaprochnost'metallov. (CNIITMASh, kn.2), Mashgiz, 1946.
9. Uprochnenie stal'nih detalej himiko-termicheskojobrabotkoj (poverhnostnoe nasyshhenie uglerodom i azotom). Metody ocenki pokazatelej kachestva /V.G.Vorob'ev, B.V.Georgievskaja, V.M.Zinchenkoidr.//M.:Izd. standartov, 1976. 64s.
10. Kantor S.I.,Shmykov A.A. O mehanizmenauglerozhivanija stali//Kontroliruemyeatmosfery: Materi-alyseminara /MDNTP im. F.Je.Dzer-zhinskogo. M., 1971. S.56—70.
11. Andreev Ju.N., Bodjachevskaja T.A., Chernjahovskij E.Z. Vlijanie tochnosti regulirovanija S-potenciala na raspredelenie ugleroda v cementovannom sloe detalej// Pechi mashinostroitel'noj promyshlennosti: Sb.trudov/ VNIPITeploproekt. M., 1975. Vyp. 36.S.45—49.
12. Gurevich A.P., Jur'ev S.F.Oroli ostatochnih naprjazhenij v povyshenii predela vynoslivosti stali pri himiko-termicheskoj obrabotke // Povyshenie ustalostnoj prochnosti detalej mashin poverhnostnoj obrabot-koj.M.,1952.S.43—63.
13. Kontporovich I.E.Termicheskajaobrabotkastaliichuguna. M.:Metallurgizdat,1950.683s.
14. Kaplun P.V. Viznachennja zalishkovih napruzhen' v azotovanih sharah pіslja іonnogo azotuvannja za pokaznikami mіkrotverdostі/ P.V. Kaplun, B.A.Ljashenko//Problemy prochnosti, №6, 2016, S. 56–63.
15. Kaplun P.V. Pіdvishhennja znosostіjkostі і dovgovіchnostі pіdshipnikіv kochennja/ P.V.Kaplun, K.A. Parshenko/ Hmel'nic'kij – HNU.– 2016.–237s.
Published
2017-10-15
Section
Articles