Надіслати статтю
вул. Інститутська 11, м. Хмельницький, 29016

ВПЛИВ ШУМІВ НА ПРОЦЕС КВАНТУВАННЯ ПЕРІОДИЧНИХ СИГНАЛІВ МЕТОДОМ ПРЯМОГО ПЕРЕТВОРЕННЯ

INFLUENCE OF NOISE ON THE PROCESS OF QUANTIFYING PERIODIC SIGNALS BY THE DIRECT CONVERSION METHOD

Сторінки: 136-140. Номер: №5, 2021 (301)
 Автори:
ПЕТРУШАК В.С., ПІДЧЕНКО С.К., ТАРАНЧУК А.А.
Хмельницький національний університет
ORCID ID: 0000-0002-7232-1044, 0000-0001-9488-1782, 0000-0001-9686-8784
e-mail: petrushak@ukr.net, sergpchn@gmail.com, allatr@ukr.net
PETRUSHAK VOLODYMYR S., PIDCHENKO SERGIY K., TARANCHUK ALLA A.
Khmelnytskyi National University
DOI: https://www.doi.org/10.31891/2307-5732-2021-301-5-136-140
Рецензія/Peer review : 02.10.2021р.
Надрукована/Printed : 10.10.2021 р.
Анотація мовою оригіналу
 Вказано на джерела шуму та проаналізовано вплив шумів під час перетворення періодичних сигналів в код методом прямого квантування. Представлені аналітичні вирази для оцінки впливу шумів на процес вимірювання. В середовищі Matlab з використанням пакету Simulink розроблено модель для  наочного дослідження впливу внутрішніх шумів на процес вимірювання параметрів амплітуди періодичного сигналу. За результатами моделювання отримана залежність сигнал/шум від частоти вхідного сигналу. Наведені графічні матеріали, які наочно демонструють вплив шумів на процес вимірювання амплітуди. Встановлено, що відношення сигнал/шум не перевищує 63 дБ на частотах вхідних синусоїдних сигналів до 210 МГц при значенні амплітуди 1В, що покращує технічні показники перетворювача.
Ключові слова: активний сенсор, амплітуда, білий шум, інтернет речей, періодичний сигнал, прямий метод квантування, телекомунікаційна мережа, цифро-аналогове перетворення.

Розширена анотація англійською мовою

In the practice of electrical and radio measurements, voltage measurement is a common operation. This determines the potential difference or voltage drop in the section of the electrical circuit (on its element). The purpose of measuring DC voltage is to determine its value and sign of polarity. When measuring AC voltage, any of its parameters can be determined (amplitude, mean, rms, rectified value or signal scope). The efforts of prominent scientists are aimed at improving the metrological and technical indicators of existing measuring instruments, in particular the development of new methods for correcting the characteristics of the transformation of the measuring channel, which is their main component. However, all these methods focus on converting the amplitude of the periodic signal into an equivalent parameter, followed by converting it into digital code. All this leads to additional conversion errors and requires additional hardware costs. Accordingly, the improvement of known methods for creating new converters of high-frequency periodic signals into code is a promising task at this stage of development of measuring technology.
The paper points to noise sources and analyzes the influence of noise during the conversion of the amplitude of periodic signals into code by direct level quantization. It is established that for industrial tomography, the influence of external factors on the probing input signal is practically absent, because the processes of cavitation and chain reaction take place in a closed environment. It was found that the internal noise is related to the technical characteristics and features of each element of the structural diagram of the converter. Analytical expressions for estimating the influence of noise on the measurement process are presented. In the Matlab environment using the Simulink package, a model was developed for visual study of the influence of internal noise on the process of measuring the parameters of the amplitude of the periodic signal. According to the simulation results, the signal / noise dependence on the frequency of the input signal is obtained. Graphic materials are presented, which clearly demonstrate the influence of noise on the amplitude measurement process. It is established that the signal-to-noise ratio does not exceed 63 dB at frequencies of input sinusoidal signals up to 210 MHz at an amplitude value of 1B, which improves the technical performance of the converter.
Keywords: active sensor, amplitude, white noise, Internet of Things, periodic signal, direct quantization method, telecommunication network, digital-to-analog conversion.

References

  1. Petrushak, O. M. Osoblyvosti vymiriuvannia amplitudy periodychnykh syhnaliv / O. M. Petrushak, V. S. Petrushak // Visnyk Khmelnytskoho natsionalnoho universytetu. Tekhnichni nauky. – 2012. – № 1. – S. 200–203.
  2. Petrushak V. S. Measurement of the amplitude of periodic signals using the Fibonacci method / V. S. Petrushak // Pribory i metody izmerenij. – 2018. – T. 9. № 2. – C. 168–173.
  3. Li P. Arhitektura interneta veshej / Li P.; perevod s angl. A. Rajtmana. – M. : DMK Press, 2019. – 454 s.
  4. № 133686 Ukraina, MPK G01L 9/08, G01L 9/12. Vymiriuvalnyi peretvoriuvach na osnovi mekhanotronnoho piezoakustychnoho datchyka tysku / A. A. Taranchuk, S. K. Pidchenko, A. A. Akulynichev, A. V. Spivak, A. I. Zhyznevskyi ; zaiavnyk i patentovlasnyk Khmelnyts. nats. universytet. – № u201807922 vid 16.07.2018 ; opubl. 25.04.2019, Biul. № 8/2019. – 6 s. : il.
  5. Helman M.M. Analoho-tsyfrovi peretvoriuvachi dlia informatsiino-vymiriuvalnykh system / Helman M.M. – M. : Vydavnytstvo standartiv, 2009. – 317 s.
  6. Yanenko A. Experimental study of microwave radiation caused by the materials contacting with human body / A. Yanenko, A. Totsky, S. K. Pidchenko, A. A. Taranchuk // Telecommunications and Radio Engineering. – 2018. – V. 77. – P. 635–644.
  7. Spetsyfikatsiia do komponenta DAC7621 Texas Instruments Incorporated, 2021. – URL : https://www.ti.com/lit/ds/sbas107/sbas107.pdf.

Post Author: npetliaks

Translate